Press "Enter" to skip to content

[2017 Cisco Hottest] 100% Pass Rate Cisco 642-883 Dumps SPROUTE PDF CCNP Service Provider Youtube Study Guide With Low Price

exam 0

How to prepare Cisco 642-883 dumps? “Deploying Cisco Service Provider Network Routing (SPROUTE)” is the name of Cisco 642-883 exam dumps which covers all the knowledge points of the real Cisco exam. 100% pass rate Cisco 642-883 dumps SPROUTE pdf youtube study guide with low price. Pass4itsure Cisco 642-883 dumps exam questions answers are updated (130 Q&As) are verified by experts.

The associated certifications of 642-883 dumps is CCNP Service Provider. You can save and learn lot more with Pass4itsure https://www.pass4itsure.com/642-883.html dumps.

Exam Code: 642-883
Exam Name: Deploying Cisco Service Provider Network Routing (SPROUTE)
Q&As: 130

642-883 dumps

Pass4itsure Latest and Most Accurate Cisco 642-883 Dumps Exam Q&As

QUESTION 11
Refer to the topology diagram in the exhibit.
642-883 dumps

Which IS-IS feature could be implemented so that the return path for the packets from router Y in area 49.00AA to router X in area 49.00BB will use the more
optimal path?
A. Enable route leaking to pass Level 2 information into the Level 1 routers.
B. Change the area 49.00AA type from a stub area to a regular area.
C. Change the IS-IS administrative distance on router Y in area 49.00AA.
D. Change the IS-IS metric type from narrow to wide on all IS-IS routers.
642-883 exam Correct Answer: A
Explanation
Explanation/Reference:
Explanation:
The IS-IS routing protocol allows for a two-level hierarchy of routing information. There can be multiple Level 1 areas interconnected by a contiguous Level 2
backbone. A router can belong to Level 1, Level 2, or both. The Level 1 link-state database contains information about that area only. The Level 2 link-state
database contains information about that level as well as each of the Level 1 areas. An L1/L2 router contains both Level 1 and Level 2 databases. It advertises
information about the L1 area to which it belongs into L2. Each L1 area is essentially a stub area. Packets destined for an address that is outside of the L1 area
are routed to the closest L1/L2 router to be forwarded on to the destination area. Routing to the closest L1/L2 router can lead to sub-optimal routing when the
shortest path to the destination is through a different L1/L2 router.
Route leaking helps reduce sub-optimal routing by providing a mechanism for leaking, or redistributing, L2 information into L1 areas. By having more detail about
inter area routes, an L1 router is able to make a better choice with regard to which L1/L2 router to forward the packet.
QUESTION 12
Refer to the exhibit.

642-883 dumps

Which two configuration options can be used to optimize the IS-IS network scenario? (Choose two.)
A. Change the R1 and R2 IS type to Level 2.
B. Change the R1 and R2 IS type to Level 1.
C. Change the gi0/0 interface IS-IS circuit type on R1 and R2 to Level 2 only.
D. Change the gi0/1 interface IS-IS circuit type on R1and R2 to Level 1.
E. Change the IS type for all the routers to Level-1-2.
F. Change the IS-IS network type for all the routers to point-to-point.
Correct Answer: CD
Explanation
Explanation/Reference:
Explanation:
QUESTION 13
The Cisco 642-883 dumps IOS XE Software summary-address router IS-IS configuration command can be used to send a summarized route into which IS-IS hierarchy?
A. Level 1 only
B. Level 2 only
C. Level-1-2 only

D. Level 1 or Level 2 or Level-1-2
Correct Answer: D
Explanation
Explanation/Reference:
Explanation:
642-883 dumps

QUESTION 14
Refer to the Cisco IOS XE IS-IS configuration exhibit.
642-883 dumps

What are two problems with the configuration that are causing the IPv4, or the IPv6, or the IPv4 and IPv6 IS-IS operations to fail? (Choose two.)
A. The configuration is missing the interface gi0/0 and interface gi0/0 commands under router isis 1.
B. The configuration is missing the address-family ipv4 unicast and address-family ipv6 unicast commands under router isis 1.
C. IPv6 unicast routing has not been enabled globally on the Cisco IOS XE router.
D. The gi0/0 and gi0/1 interfaces are not participating in the router isis 1 routing instance.
E. Multitopology IS-IS must be enabled to support both IPv4 and IPv6.
F. Another router isis instance must be enabled to support IPv6.
Correct Answer: CD
Explanation
Explanation/Reference:
Explanation:
· When using user-network interface (UNI) or enhanced network interface (ENI) ports for any IPv6-related features, you must first globally enable IP routing and
IPv6 routing on the switch by entering the ip routing ipv6 unicast-routing
QUESTION 15
In which network environment is IS-IS adjacency check important?
A. in a multitopology environment where there are different instances of IS-IS running on the same router
B. in an IPv4/IPv6 environment and running single-topology IS-IS
C. when a level L1/L2 IS-IS router is neighboring with a Level 1 only or Level 2 only router
D. when IS-IS neighbors are in an NBMA environment like over Frame Relay
E. when IS-IS neighbors are in a broadcast environment like an Ethernet LAN
642-883 pdf Correct Answer: B
Explanation
Explanation/Reference:
Explanation:

642-883 dumps

QUESTION 16
Refer to the IS-IS configuration exhibit.
642-883 dumps

This is the typical IS-IS configuration of the routers in an AS using IS-IS as the IGP. This AS is in the transition phase of integrating IPv6 into the network. During
this transition phase, some of the routers within the AS might be running IPv4 only, some might be running IPv6 only, and others might be running both IPv4 and
IPv6. To avoid any black holes for the IPv6 traffic, which configuration change can be made?
A. Disable IS-IS adjacency checks.
B. Enable IPv6 adjacency over IPv4 IS-IS peering.
C. Enable multi-topology IS-IS.
D. Disable the IPv4 unicast address-family.
E. Enable IS-IS wide metric to support the single-topology mode.
Correct Answer: C
Explanation
Explanation/Reference:
Explanation:
QUESTION 17
When implementing OSPF, which type of networks require DR/BDR election?
A. point-to-point networks
B. mutli-access broadcast networks
C. non-broadcast multi-access networks (Hub and Spoke Frame Relay) using point-to-multipoint OSPF network type
D. All networks type
642-883 vce Correct Answer: B
Explanation
Explanation/Reference:
Explanation:
QUESTION 18
The S bit in the MPLS header is used for what purpose?
A. To indicate the bottom level in the label stack
B. To indicate if LDP is sync to the IGP
C. To indicate if LDP is sync to the IGP
D. To indicate the status of the LSP
Correct Answer: A
Explanation
Explanation/Reference:
Explanation:
642-883 dumps

a 1-bit bottom of stack flag. If this is set, it signifies that the current label is the last in the stack.
QUESTION 19
What are two purposes of the BGP scan-time command? (Choose two.)
A. to tune the BGP process which walks the BGP table and confirms the reachability of next hops
B. to allow faster detection of downed BGP peers
C. to improve BGP convergence time
D. to tune the BGP update interval
E. to decrease the effects of unstable routes by increasing the route suppression time
642-883 exam Correct Answer: AC
Explanation
Explanation/Reference:
Explanation:
Background BGP scanner
It is responsible for BGP housekeeping by scanning both the BGP RIB and the IP RIB and cleaning and sorting things out.
BGP monitors the next hop of the installed routes to verify next-hop reachability and to select, install, and validate the BGP best path. By default, the BGP scanner
polls the RIB for this information every 60 seconds.
During the 60 second time period between scan cycles, IGP instabilities or other network failures can cause temporarily black holes and routing loops.
NOTE With Cisco IOS the default timer is 60 seconds for the IPv4 address family and 15 seconds for the
VPNv4 address family in order to optimize the VPNs routing table convergence.
This timer can be controlled via the following command:
Router(config-router)#bgp scan-time <5-60>
QUESTION 20
When using the show bgp ipv6 unicast summary command to verify the IPv6 BGP 642-883 dumps session status with the IPv6 BGP peers, you noticed the “St/PfxRcd” status for one of the IPv6 BGP peers is in the “Active” state. What does the “Active” state indicate?
A. The IPv6 BGP session has been established with the IPv6 BGP peer.
B. The router is in the process of sending BGP routing updates to the IPv6 BGP peer.
C. The router is in the process of establishing the IPv6 BGP session with the IPv6 BGP peer.
D. The router is exchanging BGP notification messages with its IPv6 BGP peer.
Correct Answer: C
Explanation
Explanation/Reference:
Explanation:

642-883 dumps

Containing all our Cisco 642-883 dumps practice exam questions (Q&A), practice testing software and other exam preparation materials, this dumps is highly recommended to excel in all the Cisco https://www.pass4itsure.com/642-883.html dumps exam technologies.

Read More Youtube:https://youtu.be/ZMl1uk-Nqwk